|
Who's Online
There currently are 5967 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I was having a hard time finding the problem with this Mackie 1604 unit. I didn't have a schematic. Went looking on the web and found your site and the price was more then reasonable. Ordered it and within the hour had the manual and within 15 minutes had the unit fixed. Best $4.99 I ever spent. Thank you.
Doug
;
This is a service manual in every sense of the word ( French and German versions of the text are included, as well as English..)
There are explanations of the mechanical and electrical functions, plenty of mechanical drawings, and the needed schematics. The quality of the scanning is excellent - all the component values are clearly legible - and very usefully there are pcb component layouts, so you can find a component on the schematic, and then very quicky pinpoint its physical location on the relevant pcb.
I cannot see how I can give this manual any less than the maximum 5 stars! Great value for money, which will pay for itself immediately. Excellent all round!
;
the manual is great and especially hard to find... thanks for the great service and having a hard to find manuel_
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.50 of store credit for Your review.
;
hat alles sehr gut geklappt. Das Servicemaual ist gut zu verwenden. Die Pläne und Schrift
ist klar und leserlich. Außerdem preiswert. Grüße an alle Hifi-Bastler
Trouble Shooting Guide, Standard
If the fault remains, send the unit on according to the local company directives. 2 - VDIG (3.2 V) is incorrect: Replace N701. If that does not help, send the unit on according to the local company directives. 3 - I2CDAT (3.2V) is incorrect: Measure the resistance of R619 (6.8 kohms). Check the soldering at D600:3. If both the resistance and the soldering are correct, replace D600. 5 - I2CCLK (3.2 V) is incorrect: Measure the resistance of R620 (6.8 kohms). Check the soldering at D600:4. If both the resistance and the soldering are correct, replace D600.
5.4
The display is black
Open the phone and check for liquid damage. Try again using a display you know is correct. If the fault remains, measure the resistance of R808 (33 kohms). If the resistance is very low, replace C824 and C826, otherwise replace R807 and R808. If the fault still remains, send the unit on according to the local company directives.
5.5
The background illumination to the display is missing or faintly glowing
Open the phone and check for liquid damage. Make sure that all LEDs (H651, H652, H653 and H654) are mounted and correctly soldered. Give the board power and start the board. If only a couple of the LEDs are faulty, replace them. If none of the LEDs are lit, measure the resistance on one of them. If the resistance is 0 ohm, there is a damaged foil in at least one of the LEDs. Remove the LEDs one by one in the following order: H654; H651, H653 and finally H652. Measure the resistance after each removal. When the resistance increases, the fault is found. If the resistances of the LEDs are too high, make sure that VBATT exist on them. If VBATT is missing, the phone is probably liquid damaged. If VBATT is correct, make sure R607 (1.0 kohm) and R609 (2.7 ohms) are mounted and correctly soldered. If none of the LEDs H651-H660 are lit, measure the voltage at R607, on the pin closest to D600 (0.55 V). Before measuring you have to press one of the keys to let the processor set LED3K high for approximately 10 seconds. If the voltage is missing, check the soldering at D600:69. If the soldering is correct, replace D600. If the fault still remains, send the unit on according to the local company directives.
4/00021-2/FEA 209 544/16 G
17(28)
$4.99 A1018S ERICSSON User Guide It's a complete guide ( also known as operating manual or owner's manual), and it's in PDF format. A…
|
|
|
> |
|